- Manuals
- Brands
- Lewmar Manuals
- Fishing Equipment
- Fish 700
- Product manual
Pro series
Hide thumbs Also See for Fish 700:
- Product manual (28 pages)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Table Of Contents 17
-
- Contents
- Table of Contents
- Troubleshooting
- Bookmarks
Table of Contents
-
Electric Specifications
-
Product Support
-
Safety Notice
-
Windlass General
-
Fitting
-
Electrical
-
Installation
-
Gypsy Suitability
-
Above Deck Preparation
-
Below Deck Preparation
-
Above Deck Fitting
-
Under Deck Fastening
-
Loading Rope/Chain
-
Electrical Wiring
-
Electric Cable Selection
-
Control Switch Installation
-
Wiring Diagram Using Contactor Provided (Part no 68000939)
-
Wiring Diagram if a Contactor Box (Part no 68000965) Is Used
-
Wiring Diagram if a Pre-Wired Control Box (Part no 68000963) Is Used
- Operation
-
Manual Controlled Freefall
- Pro-Fish
-
Pro-Series
-
Manual Anchor Recovery
-
Power Up/Down
-
Servicing Schedule
-
Gypsy Replacement/Service
- Parts List
- Troubleshooting
-
Warranty
Advertisem*nt
Quick Links
- 1 Installation
- 2 Operation
- 3 Pro-Fish
- 4 Gypsy Replacement/Service
- 5 Parts List
- 6 Troubleshooting
- Download this manual
Pro-Series /Fish Windlasses
Product manual
Table ofContents
Advertisem*nt
Table of Contents
Related Manuals for Lewmar Fish 700
-
Fishing Equipment Lewmar Pro Series Product Manual
(28 pages)
-
Fish windlass (25 pages)
-
Fishing Equipment Lewmar pro-sport series Owner's Manual
Fish windlass (35 pages)
-
Fishing Equipment Lewmar CPX Product Manual
Vertical windlass (30 pages)
Summary of Contents for Lewmar Fish 700
- Page 1 Pro-Series /Fish Windlasses Product manual...
- Page 2 1- Introduction Thank you for choosing Lewmar. Lewmar products are world renowned for their quality, technical innovation and proven performance. With a Lewmar product you will be provided with many years of outstanding service. Product support Lewmar products are supported by a worldwide network of distributors and Authorised Service Repre- sentatives.
- Page 3 • Boating, like many other activities can be hazardous. Even the correct selection, maintenance and use of proper equipment cannot eliminate the potential for danger, serious injury or death. • Lewmar windlasses are designed and supplied for anchor control in marine applications and are not to be used in conjunction with any other use.
- Page 4 • Suitable electrical cable and crimp terminals • 76mm (3”) Hole Saw 4.2 Accessories Use only genuine Lewmar parts and accessories to ensure top performance and eliminate the risk of voiding your warranty. 4.3 Gypsy Suitability Gypsies fitted to the Pro-Series / Pro-Fish windlasses are ideally suited to handling our factory made Rope/Chain combination rodes, which consist of rope spliced to a chain tail.
- Page 5 6mm - ” 4.8 Loading rope/chain For safety and performance Lewmar recommends the use of matched Lewmar anchor rodes. WARNING! Isolate (turn off) the windlass using circuit breaker / isolator. 1. Pull out control arm. 2. Feed anchor rope/chain into entry hole. Tie off to suitable strong point in the anchor locker.
- Page 6 5- Electrical wiring 5.1 Electric cable selection Lewmar recommends the installer source and install cable that meets the requirements of the standards and regulations relevant to the installation and codes of practice. The cable table gives recommended cable sizes based on total length of cable required, from the battery, following the route of the cables.
- Page 7 5.4 Wiring diagram using contactor provided (Part No 68000939) Installation instructions are supplied separately with any accessories. Lewmar Pro-Series/Fish windlass ref B10414 iss.1...
- Page 8 5.5 Wiring diagram if a contactor box (Part No 68000965) is used Installation instructions are supplied separately with any accessories.
- Page 9 5.6 Wiring diagram if a pre-wired control box (Part No 68000963) is used Installation instructions are supplied separately with any accessories. Lewmar Pro-Series/Fish windlass ref B10414 iss.1...
- Page 10 2. Release any anchor locks 3.When safe insert the Lewmar wrench in to the capstan drive cap. Rotate clockwise to grip the gypsy and anticlockwise to free the gypsy controlling the rate of descent of the anchor. Once deployed adjust desired scope if using a rope/chain, lock the clutch by turning the drive cap clockwise and engage the anchor locks.
- Page 11 1. Ensure capstan drive cap is tight so the clutch is locked. 2. Release any anchor locks and when safe insert the Lewmar wrench or a standard 12mm (1/2”) drive rachet into the socket end of the driveshaft on the opposite site of the windlass to the gypsy.
- Page 12 6.3 b - Pro-Series To release anchor: To retrieve anchor: 1. Check clutch nut is tight. If the clutch nut is not tight 4. Press the UP button continuously to retrieve the the internal clutch will rotate freely and not engage anchor.
- Page 13 • Re-Assemble, use grease to hold the drive pins (43) in place and small amount on the mating faces. • Use loctite on the screws (53) and (54) and Pro-Fish cap screw (17), making sure no Loctite residue ® gets on the thread as it will prevent the free fall function operating. Lewmar Pro-Series/Fish windlass ref B10414 iss.1...
- Page 14 7.3 Parts list...
-
Page 15: Troubleshooting
If okay, replace the contactor. • Check the voltage at the motor. If voltage of at least 12.5 volts is present and the motor does not operate, the motor is defective. Lewmar Pro-Series/Fish windlass ref B10414 iss.1... - Page 16 Lewmar grants no other warranties regarding the iii Lewmar shall not be liable in any way for Product fitness for purpose, use, nature or satisfactory quality failure, or any resulting loss or damage that arises of the products.
This manual is also suitable for:
Pro-fish pbFish 1000
